Herbicides for Glyceria Control

Glyceria Flower1Disclaimer
These herbicide recommendations are made subject to the product being registered for that purpose under relevant legislation. It is the user's responsibility to check that registration or an off-label permit covers the proposed use. Always read the herbicide label.

If in doubt, visit the Australian Pesticides and Veterinary Medicines Authority (APVMA) website at www.apvma.gov.au.

Only herbicides registered for use in pasture and non-cropping situations - or included under off-label provisions - are listed in the following table. For recommendations in specific crops consult an agronomist.

Care must be taken in using herbicides as non-target plants contacted may be harmed.

Wetting agents

Most herbicides require a wetting agent for best results. Carefully consult the product label for specific directions regarding any adjuvants.

Waterways and wetlands

Be careful! Many herbicides can cause damage to waterways and wetlands. Check the herbicide label directions carefully before use near waterways and wetlands. For more information see Guidelines for Safe and Effective Herbicide Use Near Waterways.

Herbicide brands and concentrations

Herbicides are referred to by the active chemical ingredient in the following table. The product trade names in this publication are supplied on the understanding that no preference between equivalent products is intended and that the inclusion of a product does not imply endorsement by DPIPWE over any other equivalent product from another manufacturer. Information on available brands containing the herbicide you require should be obtained from a reputable herbicide supplier or the APVMA website at www.apvma.gov.au.

There may be a number of products with the same active ingredient but with alternate formulations (concentration) registered for control of a weed eg: Glyphosate 360 g/L, Glyphosate 450 g/L may be registered for use on the same weed. Alternate formulations such as these will have a different application rate. ALWAYS check the label.

In and around waterways

Type of application
Herbicide (active ingredient)
Commercial products (content of active ingredient)
Rate of commercial product per litre
Comments
Spot SprayGlyphosateRoundup Biactive®
(360 g/L)
10 ml/LApply to actively growing plants at the mature head stage in late Summer/Autumn.

DO NOT use additional
surfactant/wetting agent unless it is approved for use in aquatic situations.

DO NOT apply this product within 0.5 km up-stream of potable water intake in flowing water (i.e. river or stream, etc). or within 0.5 km of a potable water intake in a standing body of water such as a lake, pond or reservoir.

Applications to moving bodies of water should be made while travelling upstream wherever possible to prevent concentration of this herbicide in water.
Boom SprayGlyphosateRoundup Biactive®
(360 g/L)
6 L/haApply to actively growing plants at the mature head stage in late Summer/Autumn.

DO NOT use additional surfactant/wetting agent unless it is approved for use in aquatic situations.

DO NOT apply this product within 0.5 km up-stream of potable water intake in flowing water (i.e. river or stream, etc). or within 0.5 km of a potable water intake in a standing body of water such as a lake, pond or reservoir.

Applications to moving bodies of water should be made while travelling upstream wherever possible to prevent concentration of this herbicide in water


Dry channels, drains and roadsides

Type of application
Herbicide (active ingredient)
Commercial products (content of active ingredient)
Rate of commercial product per litre
Comments
Spot SprayGlyphosateRoundup Biactive®
(360 g/L)

Roundup®
(360 g/L)

10 ml/L




Apply to actively growing plants at the mature head stage in late Summer/Autumn. Add a non-ionic surfactant (50-60% ai) at 200-250 ml/100 L.

DO NOT allow water to return to dry channels and drains within 4 days of application.
Boom SprayGlyphosateRoundup Biactive®
(360 g/L)

Roundup®
(360 g/L)

6 L/ha

Apply to actively growing plants at the mature head stage in late Summer/Autumn. Add a non-ionic surfactant (50-60% ai) at 200-250 ml/100 L.

DO NOT allow water to return to dry channels and drains within 4 days of application.

    Important Disclaimer
    To the extent permitted by law, the Tasmanian Department of Primary Industries, Parks, Water and Environment (including its employees and consultants) excludes all liability to any person for any consequences, including but not limited to all losses, damages, costs, expenses and any other compensation, arising directly or indirectly from using information or material (in part or in whole) contained on this website.

Back Home